Moonshine Stills and Micro Distillery Equipment

If you have the skills necessary to solder copper and want to make a 3" pot still, this kit is for you. Fits on modern beer kegs with a 2" x 3" adapter. Comes with all the parts, thermometer and garden hose attachments shown in the listing photos. Similar kits available online do not come with the clamp & gasket, hose kit, or thermometer.

Total column height is 21"

total condenser length is 40" - 3/4" pipe

water jacket length is 24" - 1 1/4" pipe

Made with heavy gauge type M copper pipe.

We do not use cheap, thin walled Drain Waste Vent (DWV) pipe on our stills.

The stainless steel ferrule can not be soldered and must be silver brazed or TIG welded which requires special skills and equipment, so we have given you the option of having us braze it or you can do it yourself. If you have us braze the ferrule, we also drill the stops out of the condenser tees so you don't have to buy an expensive drill bit. If you choose not brazed, some fitting may be required.

If you have the skills necessary to solder copper and want to make a 2 inch still, the 2 inch pot still diy kit is for you. Fits on modern beer kegs with a tap fitting of 2 1/2" O.D. Comes with all the parts and thermometer shown in the listing photos. Also included are the garden hose attachments.

This still will produce around 2 gallons per hour of 120-140 proof alcohol. A higher proof can be obtained with multiple distillations. This still is the same one we use on our beer keg whiskey still.

See video below.

Choose from digital or hermetically sealed dial thermometer.

This kit is for building our 2" cooling management still column. Check photos to see finished product. Column is 34 inches long. 

Made with heavy gauge type L copper pipe.

We do not use cheap, thin walled Drain Waste Vent (DWV) pipe on our stills.

The kit comes with all copper parts pre-cut and ready for assembly. Also included is the fully assembled flow control kit and cooling hoses, clamp and gasket, digital thermometer and copper mesh packing.

The stainless steel ferrule can not be soldered and must be silver brazed or TIG welded which requires special skills and equipment, so we have given you the option of having us braze it or you can do it yourself. If you have us braze the ferrule, we also drill the stops out of the condenser tees so you don't have to buy an expensive drill bit. If you choose not brazed, some fitting may be required.

This still will run up to 3 gallons per hour as a pot still (120-140 proof) and 1-2 gallons per hour when run as a reflux column (150-180 proof).

See it run on video below

A proven traditional still design made with modern equipment. The beer keg whiskey still uses our 2" pot still along with our beer keg thumper attachment. All piping is 3/4 inch. Stainless steel kegs or kettles will retain heat much better than copper pots, causing the still to run faster and be much more stable during operation.

Made with heavy gauge type L copper pipe.

Currently shipping in 2-3 weeks.

We do not use cheap, thin walled Drain Waste Vent (DWV) pipe on our stills.

This still is capable of producing 170 proof at a rate of 2 gallons per hour. No modifications to your beer kegs are necessary to use this kit. It comes with the necessary clamps & gaskets.

Scroll down to watch video.

This still comes with everything you see in the photos except the kegs. The liebig condenser can be attached directly to the still head and used as a stand alone pot still for stripping runs. No worm condenser is necessary.

Garden hose attachments clamps, gaskets & digital thermometer included.

Parts come soldered and polished. No soldering required

Kit can be purchased with digital or dial thermometer. Our new thermoport allows you to use the digital or dial thermometer without any modifications. Choose thermometer below.

Our thumper/doubler - 5 gallon is made from 304 stainless steel with a copper thumper head. The 5 gallon can comes with an 8 inch lid, thermometer and drain. The copper thumper head is made from 3/4” copper pipe and comes with unions so you can attach your accessories easily.

Want to turn your 5 gallon tall or 15.5 gallon beer keg into a thumper or doubler for your still? This is what you need. This listing is for the copper attachment only. Keg not included

This unit is ready to go for a 5 gallon tall or 15.5 gallon keg and can be cut down to fit a pony keg. It is ready to attach to your beer keg with the included clamp & gasket. Constructed from heavy duty type L copper pipe. The tubes are 3/4" pipe and are easily necked down to 1/2" if you have a still with 1/2" piping. 3/4" copper unions included. Down tube is perforated at the bottom. Smaller bubbles mean higher proof.

The inline copper proofing parrot comes with a 2” tri clover connection and a bypass valve for when proofing is not desired. It can handle high flow rates with exceptional accuracy. The accuracy is due to the small diameter of the alcohol meter chamber, which minimizes mixing. All copper construction with lead free valve.

Buy it with or without an alcohol meter.

Select below

This parrot is a full size, professional distillers proofing parrot. At 24 inches tall, it can handle high flow rates with exceptional accuracy. The accuracy is due to the small diameter of the alcohol meter chamber, which minimizes mixing. All copper construction with a very stable 4" stainless steel base.

Designed to be used with a standard 1 gallon glass jug. (see photos)

*Alcohol meter sold separately.

Building your own moonshine column still?  We can help! 

The hardest part of building a still is making the connection between your kettle and the column. We did the hard part for you. We silver brazed a 2" 304 Stainless Steel ferrule onto 2" heavy duty type L copper pipe. We do not use cheap, thin walled Drain Waste Vent (DWV) pipe on our stills.

These do it yourself column kits include a stainless steel tri-clamp & gasket and come in lengths of 1, 2, and 3 feet.

This is heavy duty type L pipe, not cheap DWV pipe that some of our competitors use. For our silver brazing we use 56% food grade silver - guaranteed to be safe. The column kits will work on modern beer kegs and commercially available kettles as well.

Your order will be shipped with the beer keg o-ring. If you are planning on using this on a commercial kettle just email us after you buy and tell us to send you the tri-clamp gasket instead of the beer keg o-ring.

Choose from different lengths below.

*column kits do not come polished.

These 2" still heads include a digital thermometer and a stainless steel tri-clamp & gasket. Comes with 3/4” union on the output. It can be easily necked down to 1/2” copper pipe or copper tubing for a worm coil. These will work on most beer kegs and commercially available 2 inch kettles.

Made with heavy duty type L copper pipe.

We do not use cheap, thin walled Drain Waste Vent (DWV) pipe on our stills.

Comes with clamp, gasket & digital thermometer.

Choose column length below.

These 2" still heads include a dial thermometer and a stainless steel tri-clamp & gasket. Comes with 3/4” union on the output. It can be easily necked down to 1/2” copper pipe or copper tubing for a worm coil. These will work on most beer kegs and our 2 inch kettles.

Made with heavy duty type L copper pipe.

We do not use cheap, thin walled Drain Waste Vent (DWV) pipe on our stills.

Comes with clamp & gasket.

Choose column length below.

These moonshine still heads can be ordered in lengths of 1, 2 and 3 feet (2 foot shown in photos)

They include a digital thermometer and a stainless steel tri-clamp & gasket. The included copper union is ready for attaching to 3/4" copper pipe, which can be easily necked down to copper tubing for a worm coil. A 2" x 3" reducer is necessary to attach this unit to a beer keg.

Made with heavy duty type M copper pipe.

We do not use cheap, thin walled Drain Waste Vent (DWV) pipe on our stills.

Comes with clamp, gasket & digital thermometer.

These moonshine still heads can be ordered in lengths of 1, 2 and 3 feet (2 foot shown in photos)

They include a hermetically sealed dial thermometer and a stainless steel tri-clamp & gasket. The included copper union is ready for attaching to 3/4" copper pipe, which can be easily necked down to copper tubing for a worm coil. A 2" x 3" reducer is necessary to attach this unit to a beer keg.

Made with heavy duty type M copper pipe.

We do not use cheap, thin walled Drain Waste Vent (DWV) pipe on our stills.

Comes with clamp, gasket & thermometer.

These mini still heads include a digital thermometer and a stainless steel tri-clamp & gasket. The included copper union is ready for attaching to 1/2" or 3/4" copper pipe, which can be easily necked down to copper tubing for a worm coil. These will work on most beer kegs and commercially available 2 inch kettles.

Comes with clamp, gasket & your choice of digital or dial thermometer.

If you have your own copper pipe and need to make the connection to your beer keg or kettle, this is what you need. These kits include a 2 inch copper coupler and a stainless steel tri-clamp & gasket and come ready to solder. These will work on most beer kegs and commercially available 2 inch kettles.

1/2” FPT input & output for cooling water

The whiskey cone - copper 4 x 2 inch can be used to complete your whiskey helmet and turn it into a pot still. Images show it set up on a simple still.

For maximum cooling power with the ability to knock the vapor down on stills up to 2 inches in diameter, try our copper shotgun condenser. The TIG welded 2 inch tri clover copper shotgun condenser is made from 100% copper and has 3 vapor tubes. The cooling water ports are 1/2" NPT. Total length is 17.5".

For maximum cooling power with the ability to knock the vapor down on stills up to 4 inches in diameter, try our copper shotgun condenser. The TIG welded 2 inch tri clover copper shotgun condenser is made from 100% copper and has 5 vapor tubes. The cooling water ports are 1/2" NPT. Total length is 17.5".

1/4" O.D. Copper Coil - Fits inside 2" copper pipe.

Coil length is 6 inches

This is all you need for a 2" still. Anything larger is just overkill. To see this condenser run in our stills, watch our 2" liquid management video on the videos page. This is the same condenser used on that still and it can condense up to 3 gallons per hour. 

See it run on video - click here

Our Liebig condensers - stainless steel and copper tri clamp are professionally TIG welded works of art that feature a stainless steel jacket over copper tubing. The copper fitting can be soldered or brazed to your still, allowing you to use the tri clamp connection to remove the condenser for ease of cleaning and for storage. The cooling water connections are 1/2” pipe thread. The unit comes in three lengths, short, medium and long.

Long: Total length is 36”. Jacket length is 31”.

Medium: Total length is 30”. Jacket length is 25”.

Short: Total length is 24”. Jacket length is 20”.

Constructed with a 1" water jacket over 3/4" pipe, this condenser is the same one we use on our beer keg whiskey still.

Total length is 36"

Water jacket length is 22"

The cooling ports are 1/2" so it can be easily used with a submersible pump or a garden hose. Garden hose attachments for this condenser are available in Kits & Parts.

3/4" union allows for attachment to any of our 3/4" pot still heads or your own.

Custom lengths & sizes available. Contact us for pricing.

Build your own adjustable condenser with this kit. Piping is 1" over 3/4". This is the same condenser we use on some of our 2" stills. Comes with assembly instructions.

Assembled dimensions are as follows:

Total length - 36"

Water jacket length - 24"

The Liebig condenser is a 1/2" pipe with a 3/4" water jacket. Total length is 29". The water jacket is 20". It is the same condenser we use on all of our small 2" stills.

The cooling ports are 1/2" so it can be easily used with a submersible pump or a garden hose. Garden hose attachments for this condenser are available in Kits & Parts.

1/2" union allows for attachment to any of our 1/2" pot still heads or your own.

Custom lengths & sizes available. Contact us for pricing.

Build your own adjustable condenser with this kit. Piping is 3/4" over 1/2". This is the same condenser we use on some of our 2" stills. Comes with assembly instructions.

Assembled dimensions are as follows:

Total length - 30"

Water jacket length - 18"